Rubber Bellows Mechanical Seal for Water Pumps

Rubber Bellows Mechanical Seal for Water Pumps

• Self-Aligning by Design: The flexible bellows lets the seal face follow shaft end-play and runout, so this rubber mechanical seal keeps a flat, even face contact pattern even on a worn or slightly bent shaft.

• No Set Screws, No Shaft Damage: Drive is transmitted through the bellows interference fit rather than a clamped collar, and because the elastomer bellows mechanical seal never clamps metal onto the shaft, the sealing area stays unmarked for the next rebuild.

Model:RO
WhatsApp Now
WHAT ARE YOU LOOKING FOR?
*
This field is required
Total quantity you need
*
This field is required
*
This field is required
Email format error
Due to email instability, you might miss our correspondence. Please provide your phone number for alternative contact.
This field is required
Telephone information is wrong!
Send Message

Product Overview


MIAOYU is a mechanical seal manufacturer producing the rubber bellows range for clean and lightly contaminated water duty. As an elastomer bellows mechanical seal, the design uses a moulded rubber bellows as spring carrier, secondary seal and drive element in one, so there is no O-ring sliding along the shaft and no set screws biting into it. The result is a rubber mechanical seal that absorbs shaft runout, shrugs off fibre and sediment, and rebuilds the same way after every service interval.


Because the bellows replaces both the pusher O-ring and the drive collar, this is a mechanical seal for water pumps supplied from 20 mm to 100 mm shaft diameter, with carbon, SiC or TC faces and NBR, EPDM or Viton elastomers. Every unit is dimensioned on DIN 24960 / EN 12756 working lengths, so it drops into the same chamber as the part it replaces.


Key Features


• Single Coil Spring, Clog-Resistant: One large coil spring sits behind the carbon face, clear of the pumped fluid, so fibre, sand and scale pass through the chamber instead of packing into a multi-spring nest and killing the face load.

• Water-Duty Materials as Standard: Carbon against SiC or TC faces, a stainless steel spring and metal parts, and NBR or EPDM bellows make this a mechanical seal for water pumps that also copes with light acids, alkali and oil.

• Drop-In 20–100 mm Range: Every size is built by a mechanical seal manufacturer that moulds its own bellows and laps its own faces, and is dimensioned on D1, D3, D7, L1, L3 and L4 to match the seal being replaced.



Technical Specs

Materials

Mediums

Water, oil, acids, alkali with low corrosion etc.

Stationary Ring

Carbon/Sic/TC

Temperature

-20℃ to 180℃

Rotary Ring

Sic/TC/SUS304

Pressure

≤1MPa

Secondary Seal

NBR/EPDM/Viton

Speed

≤20m/s

Spring and Metal Part

Stainless Steel


The bellows does three jobs at once: it loads the faces, seals the shaft and drives the rotating ring. Because an elastomer bellows mechanical seal has no sliding O-ring, there is nothing to hang up when the water carries sediment, and face load stays constant as the faces wear. That is the practical difference between this rubber mechanical seal and a pusher design — fewer parts to stick, and a shorter axial length for tight stuffing boxes.

CFRO-1.jpg
CFRO-2.jpg


Sizing is by shaft diameter. The table below covers 20 mm to 100 mm in 2–5 mm steps with D3, D7, L1, L3 and L4 for each size — the dimensions that decide whether a mechanical seal for water pumps will drop into an existing stuffing box without modification. Send the old seal, the pump tag or a drawing and, as a mechanical seal manufacturer, we cross-check the working length instead of guessing from the pump model. Non-standard and inch sizes are moulded to order.


Product Specifications


Metric Shaft Size D1Size CodeD3D7L1L3L4
2002003442352523
2202203644352523
2402403846352523
2502503947352523
2802804250352523
3003004452352523
3203204654352523
3303304755352523
3503504957352523
3803805464382725
4004005666382725
4204205868382725
4304305969382725
4504506171382725
4804806474382725
5005006676392725
5205206878402725
5305306979402725
5505507181402725
5805807689413028
6006007891413028
6206208093413028
6306308194413028
6506508396413028
6806808699413230
70070090101423230
75075095110423230
800800100115423331
850850105120433331
900900110125453331
950950115130453331
1001000120135453331



Workshop


This workshop is equipped with professional processing equipment and integrated with standardized material warehousing management, enabling a one-stop production process from precision machining to finished product delivery. It ensures part machining accuracy and production efficiency, meeting various high-specification manufacturing requirements. The same site moulds the bellows, laps the faces and assembles the complete unit, which is why a mechanical seal manufacturer that owns these steps can hold L1 and L3 tolerances across repeat batches instead of re-tooling for every order.


Metal Bellows Seals for High Temperature Pumps 606
Metal Bellows Seals for High Temperature Pumps 606
Metal Bellows Seals for High Temperature Pumps 606
Metal Bellows Seals for High Temperature Pumps 606



Product Research, Development and Testing


Our Product R&D and Testing focuses on optimizing seal performance through advanced simulation and material analysis. All seals undergo rigorous trials, including thermal cycling and pressure tests, to ensure durability, minimal leakage, and long service life in demanding industrial environments. Elastomer batches are screened for hardness, compression set and swell before moulding, and every elastomer bellows mechanical seal is then run through thermal cycling and a hydrostatic hold to confirm face load and leak rate.


R&D and Design.jpg
microscope.jpg
Light band detection.jpg
pressure test.jpg



Industry Solutions


Metal Bellows Seals for High Temperature Pumps 606
Metal Bellows Seals for High Temperature Pumps 606
Metal Bellows Seals for High Temperature Pumps 606
Metal Bellows Seals for High Temperature Pumps 606




Case Study


Pulp & Paper Mill: A board mill was changing pusher seals on its white water pumps every four months — fibre packed the spring nest and the O-ring hung up on a scored shaft. We supplied this rubber mechanical seal with a single coil spring set clear of the flow and a carbon / SiC face pair. The first unit ran fourteen months, and the mill standardised the rest of the line on the same build at roughly 40% below the OEM price.

Testimonials


A true drop-in replacement — no shaft marking, no re-setting, no special tools. It is the only mechanical seal for water pumps we now stock at both of our sites.

—Maintenance Manager, Paper Mill



FAQs


Q: How is an elastomer bellows seal different from an O-ring pusher seal?

A: In a pusher seal an O-ring slides along the shaft; in this design the rubber bellows flexes instead. That removes the sliding interface that hangs up on scored shafts, scale or fibre, keeps face load constant as the faces wear, and shortens the axial length. It is the reason an elastomer bellows mechanical seal is the usual upgrade on dirty, high-cycle or hard-water service.


Q: Which duties is this seal suited to?

A: Clean water, HVAC circulation, booster sets, irrigation, white water and light chemical duty from -20℃ to 180℃ — the typical envelope for a mechanical seal for water pumps. Above 1 MPa, or where the fluid attacks NBR or EPDM, we will recommend another face or elastomer combination rather than ship a standard build into a duty it cannot hold.


Q: What temperature, pressure and speed can it take?

A: -20℃ to 180℃, up to 1 MPa and 20 m/s at the faces, with carbon, SiC or TC face pairs. Those limits assume the correct elastomer: NBR for water and oil to about 100℃, EPDM for hot water and potable water, Viton for chemical duty. Pick the wrong elastomer and a rubber mechanical seal will fail long before its faces do, so send the fluid and the temperature together.


Q: How do I cross-reference my existing seal?

A: Send the pump model and tag number, the shaft diameter D1, the D3 / D7 / L1 / L3 / L4 dimensions (or the old seal itself), and the fluid with its operating temperature. We return a dimensioned drawing with the quotation, usually within one working day. Where the original is obsolete, we mould the bellows to the drawing instead of forcing a nearest-size match.


Q: Can you supply OEM or private-label seals?

A: Yes. As a mechanical seal manufacturer we mould bellows in-house, so customer-specific bellows hardness, face materials and branding are all practical. Annual frame contracts are quoted against fixed drawings, and private-label packaging and marking are handled at the factory.

Please Contact Us!

Get Started With Your Next Project.
If you have any questions about our products and services, please feel free to contact us. Our team will get in touch with you within 24 hours!
    bottom_logo

    Our company is specialized in the production of sealing materials, mechanical seals , cartridge seals.

    CopyRight © 2026 NINGBO MIAOYU MACHINERY TECHNOLOGY CO., LTD All rights reserved Sitemap  All tags  Designed by Zhonghuan Internet
    Get Your Custom Seal Solution Quote
    Tell us your sealing requirements (working conditions, media, dimensions, etc.), and our engineers will provide a tailored solution and quote within 24 hours. Your inquiry is 100% confidential.
    Company Name
    *
    This field is required
    Email
    *
    This field is required
    Email format error
    Phone
    This field is required
    Telephone information is wrong!
    Message
    *
    This field is required
    Send Message